Usbdm/cf (jmxx version): usb driver installation

Note for upgrading from version 3.x to 4.x USBDM firmware

This change is complicated by the existence of a Bootloader in the BDM firmware. If not replaced this loader will continue to use the original VID/PID. Because of this, it is desirable to completely replace the BDM firmware.
For JS16 based BDMs this is a simple process since the Freescale JS12 Bootloader software may be used to replace all the firmware. See Construction and Installation.
For JMxx based BDMs it is necessary to use a HCS08 programmer to re-program the entire device so that the Bootloader is updated when the rest of firmware is changed. If a programmer is not available then it is still possible to update the BDM firmware using the Bootloader but the Bootloader will remain unchanged. To do this it will be necessary to install the drivers twice — once for the old VID/PID used by the Bootloader and again for the new VID/PID used by the main firmware. Doing so will render any OSBDM drivers inoperable on that USB port.

Note for upgrading from version 3.x to 4.x USBDM firmware

Linux Drivers

The shell scripts supplied with the linux version should install the required information for the libusb drivers to work on a linux machine.

You will also need to make sure you have installed some libraries: (Some information posted by joncas on Freescale Forums — thanks)

  Hello PGO,
  
  I just tried your version 4.6 with Codewarrior 10.1 on a clean install of Ubuntu 11.04 (32 bit).
  In case it helps anyone else trying this, it required adding the following libraries with the Synaptic Package Manager:
    - tcl8.5 
    - libwxgtk2.8-0 
    - lbwxgtk2.8-dbg 
    - libstdc++5 
    - libxerces-c3.1
  Then it seems to run fine.
  Many thanks and best regards!
   
  Robert

Installation of USBDM USB drivers for old VID/PID

This process should only be done if you need to use the USBDM Bootloader to update an old JMxx based BDM when you do not have access to a HCS08 programmer.

Preliminary

Plug in the old BDM before proceeding.
Do not move the BDM to another port before updating the firmware as the driver installation will apply only to that port.
If the BDM has already been updated once, then it may be necessary to use the setboot.exe utility to place the BDM in ICP mode before installing the driver.

Procedure:

1. Run the zadig_XXX.exe program.

2. Choose Options->List All Devices from the menu so that all devices are available for installation.

3. Select the BDM from the list of devices. The description of the device will depend upon which device driver has been previously used. In either case check carefully that the Vendor ID and Product ID are 15A2 and 0021 respectively. Click on the Edit Desc. checkbox and change the description to something more meaningful. This will make the device easier to identify in the future.

4. Make sure that WinUSB is selected as the Target Driver
Click the Install Driver button. This will install the driver for the selected device. You may see a number of dialogues as shown above.

The device should now be using the new driver and the USBDM Bootloader program may be used to update the firmware.
If desired, a similar process may be used to restore the original libusb driver if it is needed for other devices. Just select the correct Target Driver.

Note for upgrading from version 3.x to 4.x USBDM firmware

Installation of USBDM USB drivers for Linux

There isn’t any. The installation script provided will modify the /etc/udev/rules.d file to allow access to the USBDM device. The required driver for USBDM BDM interface (LibusbV1) is included in the standard Linux (at least Ubuntu current version). The CDC (serial port) is a standard device and should also be installed without any extra steps.

If more installation is required on your version you will have to investigate this yourself. I’m not a Linux expert and I don’t have access to other versions for testing. If you find other steps are necessary then please advise and I will try to update the installation accordingly.

Installation of USBDM USB drivers for old VID/PID

This process should only be done if you need to use the USBDM Bootloader to update an old JMxx based BDM when you do not have access to a HCS08 programmer.

Preliminary

Plug in the old BDM before proceeding.
Do not move the BDM to another port before updating the firmware as the driver installation will apply only to that port.
If the BDM has already been updated once, then it may be necessary to use the setboot.exe utility to place the BDM in ICP mode before installing the driver.

Procedure:

1. Run the zadig_XXX.exe program.

2. Choose Options->List All Devices from the menu so that all devices are available for installation.

4. Make sure that WinUSB is selected as the Target Driver
Click the Install Driver button. This will install the driver for the selected device. You may see a number of dialogues as shown above.

The device should now be using the new driver and the USBDM Bootloader program may be used to update the firmware.
If desired, a similar process may be used to restore the original libusb driver if it is needed for other devices. Just select the correct Target Driver.

Installation of USBDM USB drivers for Windows

This driver allows the USBDM software to communicate with the USBDM cable. You would usually only need to install these driver files once. If you subsequently plug the USBDM cable into another USB port of the same computer the driver will be installed for that port automatically.

The required drivers are copied to the installation location as part of the installation process. The driver folder may be opened from the window’s Start Menu.

Setting up the drivers differs somewhat between the different versions of windows. In versions before Windows 7 you will be automatically prompted to install the drivers using a Found New Hardware Wizard when you first plug in the USBDM. For Windows 7 the installation will quietly fail and it is necessary to manually trigger the wizard.

Prior to Windows 7 the following sequence should occur:

1. Plug in the USBDM.
2. The Found New Hardware Wizard should appear. Select the Install from a list or a specific location option.
Select Next to continue.
3. Select the options as shown and navigate to the driver directory. «C:\Program Files\pgo\USBDM 4.7.0\USBDM_Drivers».
Select Next to continue.
4. The next step may take a while but you should eventually be presented with last dialogue shown.
Select Finish to close the dialogue.

The above sequence may be necessary a second time if you are installing a USBDM supporting a serial port connection. The serial port appears as a second device.

With Windows 7 the following sequence should occur:

1. Plug in the USBDM.
2. A small pop-up alert indicates windows is searching for the drivers.
3. Eventually this will be unsuccessful
4. You can click on the pop-up to view the result. The CDC Interface is not present on all USBDMs.
5. To properly install the drivers it is necessary to open the Computer Properties …
6. …and then the Device manager.
7. Locate the USBDM device(s), right-click and select Update Driver Software… from the menu.
8. Select the second option as we need to specify where to find the drivers.
9. Browse to the driver directory «C:\Program Files\pgo\USBDM 4.7.0\USBDM_Drivers». Make sure Include subfolders is selected.
10. The driver is signed but the driver inf files aren’t. This results in a Windows Security dialogue. It is necessary to confirm the installation.
11. Eventually the installation should complete successfully.
12. You can confirm the USBDM device in the device manager.
13. Repeat this process with the USBDM CDC Device (Serial port) if present.
14. You can confirm the USBDM serial port in the device manager. The serial port number assigned is unique to the BDM providing it has a unique serial number. This allows multiple USBDMs to be present at the one time.
After installation of the serial port you may examine or change the communication properties. Right-click on the USBDM Serial Port and select Properties.
15. The usual communication properties appear. The USBDM serial port is limited in what baud rate and options are supported. (I will eventually tell you what ones here when I get a chance to check 🙂 Advanced options are available. Click on Advanced…
16. One option worth noting is that you may also re-assign the COM port number used.

Features

This version of the code & extended hardware provides the following features:

A single BDM interface for programming and debugging of the following targets:
- Coldfire V2, V3 & V4 microcontrollers
- Kinetis ARM-Cortex microcontrollers
- MC56F80xx Digital Signal Controllers (Limited range of devices in CW 10 & stand-alone programmer)
No re-flashing of the BDM is required when changing between targets
Compatible IDEs
- Codewarrior V10.1 (Eclipse version)
  - Tested on Windows-XP-32bit, Windows-7-32bit, Windows-7-64bit
  - Tested on Ubuntu-32-bit
- Codewarrior Legacy versions CW for Coldfire V7.1 CodeWarrior for DSC56800E v8.3 (USBDM-JMxx-CF or MC56F8006Demo board only)
- Initial support for CodeSourcery Lite for Coldfire
- Initial support for Coldfire Flasher (CFFlasher)
Higher USB communication speed cf. JB16 version BDMs (USB full speed cf. USB low speed)
Vista compatible
Linux compatible
Initial Firmware programming may be done without a BDM using the JS16 USB bootloader ROM.
The Firmware in the BDM may be automatically updated using an in-circuit-programming (ICP) feature.
Hardware is physically small
HCS12, HCS08, RS08, Coldfire V1 specific features:
Target reset detection & control (required for HC12 processors). This allows HC12 processors to be reset into BDM mode as required for debugging.
- A higher BDM interface speed than the existing JB16 OSBDMs. Up to 56MHz. (BDM clock 28MHz).
- Automatic re-connection. The software has an option to continuously update the interface speed to prevent loss of communication if the target BDM interface speed changes (as may occur with clock changes on some targets).
- Control of BDM clock selection in HC12/HCS08/Coldfire microcontrollers. Most of these targets provide an alternative BDM clock selection. This can have advantages when connecting to high speed targets as the alternative clock may operate at a lower speed.
- Trial-and-error determination of communication speed for earlier HC12 targets.
- User prompting for target supply cycling with BKGD low as may be needed for HCS08 targets
Coldfire V2,3,4 specific features and limitations:
Higher communication speed with target — The target communication speed may be selected.
The BDM uses asychronous communication with the target i.e. the BDM signals are not synchronized with the target clock. This means that the BDM should not be used with early Coldfire targets. Check the description of the BDM interface timing in the appropriate Coldfire Processor manual to determine if this limitation applies.

Linux Drivers

The shell scripts supplied with the linux version should install the required information for the libusb drivers to work on a linux machine.

You will also need to make sure you have installed some libraries: (Some information posted by joncas on Freescale Forums — thanks)

  Hello PGO,
  
  I just tried your version 4.6 with Codewarrior 10.1 on a clean install of Ubuntu 11.04 (32 bit).
  In case it helps anyone else trying this, it required adding the following libraries with the Synaptic Package Manager:
    - tcl8.5 
    - libwxgtk2.8-0 
    - lbwxgtk2.8-dbg 
    - libstdc++5 
    - libxerces-c3.1
  Then it seems to run fine.
  Many thanks and best regards!
   
  Robert

Installation of USBDM USB drivers for Windows

The required drivers are copied to the installation location as part of the installation process. The driver folder may be opened from the window’s Start Menu.

Prior to Windows 7 the following sequence should occur:

1. Plug in the USBDM.
2. The Found New Hardware Wizard should appear. Select the Install from a list or a specific location option.
Select Next to continue.
3. Select the options as shown and navigate to the driver directory. «C:\Program Files\pgo\USBDM 4.7.0\USBDM_Drivers».
Select Next to continue.
4. The next step may take a while but you should eventually be presented with last dialogue shown.
Select Finish to close the dialogue.

The above sequence may be necessary a second time if you are installing a USBDM supporting a serial port connection. The serial port appears as a second device.

With Windows 7 the following sequence should occur:

1. Plug in the USBDM.
2. A small pop-up alert indicates windows is searching for the drivers.
3. Eventually this will be unsuccessful
4. You can click on the pop-up to view the result. The CDC Interface is not present on all USBDMs.
5. To properly install the drivers it is necessary to open the Computer Properties …
6. …and then the Device manager.
7. Locate the USBDM device(s), right-click and select Update Driver Software… from the menu.
8. Select the second option as we need to specify where to find the drivers.
9. Browse to the driver directory «C:\Program Files\pgo\USBDM 4.7.0\USBDM_Drivers». Make sure Include subfolders is selected.
10. The driver is signed but the driver inf files aren’t. This results in a Windows Security dialogue. It is necessary to confirm the installation.
11. Eventually the installation should complete successfully.
12. You can confirm the USBDM device in the device manager.
13. Repeat this process with the USBDM CDC Device (Serial port) if present.
14. You can confirm the USBDM serial port in the device manager. The serial port number assigned is unique to the BDM providing it has a unique serial number. This allows multiple USBDMs to be present at the one time.
After installation of the serial port you may examine or change the communication properties. Right-click on the USBDM Serial Port and select Properties.
15. The usual communication properties appear. The USBDM serial port is limited in what baud rate and options are supported. (I will eventually tell you what ones here when I get a chance to check 🙂 Advanced options are available. Click on Advanced…
16. One option worth noting is that you may also re-assign the COM port number used.

Alternative Driver Installation Method for Windows

Alternatively, zadig may be used to install the libusbV1 drivers for the BDM interface (not the Serial port). http://www.libusb.org/wiki/libwdi/zadig

Preliminary

Download the current version of the required driver installation program from or using the direct link (at this time) zadig.exe.
Plug in the programmed BDM.
Cancel any dialogues prompting to install the device drivers.
Under Windows 7 the automatic driver installation will proceed and fail.

This following process will install the correct libusb 1.0 driver.

1. Run the zadig_XXX.exe program.

2. Select the BDM from the list of devices. Under Windows Vista and Windows 7 the device description will be USBDM BDM Interface. Under Windows XP it may simply appear as USB Device.
- Check carefully that the Vendor ID and Product ID are 16D0 and 0567 respectively. There may also be a third number if the USBDM has a serial interface. This should be zero(0) if present.
- If the description is anonymous click on the Edit Desc. checkbox and change it to something more meaningful.
- Check that the WinUSB driver is the Target.

3. Click the Install Driver button. This will install the driver files. You may see a number of dialogues.

Select Yes to replace any existing driver

This may take a while!

Note if successful and then Close

Select Yes to refresh the list of devices.

4. If you now plug in an updated BDM to another USB port the Found New Hardware wizard should automatically appear. If prompted accept the recommended options to install the driver. Under Windows-7 there may be a prompt to accept an unsigned driver.

5. The Found New Hardware wizard should now complete. Just click Finish to close the dialogue.

Note for upgrading from version 3.x to 4.x USBDM firmware

Installation of USBDM USB drivers for old VID/PID

This process should only be done if you need to use the USBDM Bootloader to update an old JMxx based BDM when you do not have access to a HCS08 programmer.

Preliminary

Plug in the old BDM before proceeding.
Do not move the BDM to another port before updating the firmware as the driver installation will apply only to that port.
If the BDM has already been updated once, then it may be necessary to use the setboot.exe utility to place the BDM in ICP mode before installing the driver.

Procedure:

1. Run the zadig_XXX.exe program.

2. Choose Options->List All Devices from the menu so that all devices are available for installation.

4. Make sure that WinUSB is selected as the Target Driver
Click the Install Driver button. This will install the driver for the selected device. You may see a number of dialogues as shown above.

The device should now be using the new driver and the USBDM Bootloader program may be used to update the firmware.
If desired, a similar process may be used to restore the original libusb driver if it is needed for other devices. Just select the correct Target Driver.

Installation of USBDM USB drivers for Linux

Features

This version of the USBDM code combined with the FRDM-xxxx board provides the following features:

A SWD interface for programming and debugging of Kinetis ARM-Cortex microcontrollers.
Both the on-board target device (e.g. MKL25Z128M4) and external devices may be programmed.
Installation of the USBDM software does not require any tools other than the FRDM-KL25Z board.
Compatible IDEs
- Codewarrior V10.x (Eclipse version). The following features are provided:
- Eclipse (including Freescale Kinetis Design Studio). The following features are provided:
  - Kinetis New Project Wizard
  - Kinetis USBDM debug target
  - Integration of GCC tools (GNU tools for ARM or KDS tools)
  - Peripheral Register view tailored for Kinetis devices.
Stand-alone Kinetis programmer utility.
Linux compatible
Windows compatible
The Firmware in the BDM may be updated using the usual FRDM-KL25 Bootloader function.
The original board software may be restored if USBDM is not found suitable.

The capabilities and features of the USBDM interface varies between the different versions of hardware. Not all of the functionality described in the following pages may apply to this version.

Installation of USBDM USB drivers for Windows

The required drivers are copied to the installation location as part of the installation process. The driver folder may be opened from the window’s Start Menu.

Prior to Windows 7 the following sequence should occur:

1. Plug in the USBDM.
2. The Found New Hardware Wizard should appear. Select the Install from a list or a specific location option.
Select Next to continue.
3. Select the options as shown and navigate to the driver directory. «C:\Program Files\pgo\USBDM 4.7.0\USBDM_Drivers».
Select Next to continue.
4. The next step may take a while but you should eventually be presented with last dialogue shown.
Select Finish to close the dialogue.

The above sequence may be necessary a second time if you are installing a USBDM supporting a serial port connection. The serial port appears as a second device.

With Windows 7 the following sequence should occur:

1. Plug in the USBDM.
2. A small pop-up alert indicates windows is searching for the drivers.
3. Eventually this will be unsuccessful
4. You can click on the pop-up to view the result. The CDC Interface is not present on all USBDMs.
5. To properly install the drivers it is necessary to open the Computer Properties …
6. …and then the Device manager.
7. Locate the USBDM device(s), right-click and select Update Driver Software… from the menu.
8. Select the second option as we need to specify where to find the drivers.
9. Browse to the driver directory «C:\Program Files\pgo\USBDM 4.7.0\USBDM_Drivers». Make sure Include subfolders is selected.
10. The driver is signed but the driver inf files aren’t. This results in a Windows Security dialogue. It is necessary to confirm the installation.
11. Eventually the installation should complete successfully.
12. You can confirm the USBDM device in the device manager.
13. Repeat this process with the USBDM CDC Device (Serial port) if present.
14. You can confirm the USBDM serial port in the device manager. The serial port number assigned is unique to the BDM providing it has a unique serial number. This allows multiple USBDMs to be present at the one time.
After installation of the serial port you may examine or change the communication properties. Right-click on the USBDM Serial Port and select Properties.
15. The usual communication properties appear. The USBDM serial port is limited in what baud rate and options are supported. (I will eventually tell you what ones here when I get a chance to check 🙂 Advanced options are available. Click on Advanced…
16. One option worth noting is that you may also re-assign the COM port number used.

Usb driver installation

Note for upgrading from version 3.x to 4.x USBDM firmware

Note for upgrading from version 3.x to 4.x USBDM firmware

Linux Drivers

Installation of USBDM USB drivers for old VID/PID

Note for upgrading from version 3.x to 4.x USBDM firmware

Installation of USBDM USB drivers for Linux

Installation of USBDM USB drivers for old VID/PID

Installation of USBDM USB drivers for Windows

Features

Linux Drivers

Installation of USBDM USB drivers for Windows

Alternative Driver Installation Method for Windows

Note for upgrading from version 3.x to 4.x USBDM firmware

Installation of USBDM USB drivers for old VID/PID

Installation of USBDM USB drivers for Linux

Installation of USBDM USB drivers for Linux

Features

Installation of USBDM USB drivers for Windows

Похожие записи: